牙种植术中钻孔提拉方式及冷却系统对术区温度的影响

上海口腔医学 ›› 2014, Vol. 23 ›› Issue (2): 149-153.

牙种植术中钻孔提拉方式及冷却系统对术区温度的影响

刘道杨¹, 吴煜农¹, 陈宁¹, 彭伟², 廖文清², 王琰玲¹

1.南京医科大学口腔医院口腔颌面外科, 江苏南京 210029;
2.浙江工业大学机械工程学院, 浙江杭州 310000

收稿日期:2013-06-03 出版日期:2014-04-20 发布日期:2014-05-21
通讯作者: 吴煜农, E-mail:yunongwu@yahoo.com.cn
作者简介:刘道杨(1974-), 男, 在读博士研究生, 主治医师, E-mail:liudaoyang6@163.com
基金资助:
江苏省高校优势学科建设工程资助项目(2011-137)

The influence of drilling pulling ways and cooling systems on dental implant surgery

LIU Dao-yang¹, WU Yu-nong¹, CHENG Ning¹, PENG Wei², LIAO Wen-qing², WANG Yan-ling¹

1.Department of Oral and Maxillofacial Surgery, Affiliated Stomatological Hospital of Nanjing Medical University. Nanjing 210029, Jiangsu Province;
2.College of Mechanical Engineering, Zhejiang University of Technology. Hangzhou 310000, Zhejiang Province, China

Received:2013-06-03 Online:2014-04-20 Published:2014-05-21

摘要/Abstract

摘要： 目的: 研究牙种植术中不同钻孔提拉方式及不同冷却系统对术区牙槽骨温度的影响, 探讨牙种植术中温度场的变化。方法: 制作48个统一标准的模拟骨块, 根据不同钻孔提拉方式和不同冷却系统分为6组, 每组8个骨块, 进行温度场试验, 测定不同骨块中温度场的温度最高值。采用SPSS12.0软件包对数据进行单因素方差分析。结果: 在相同的钻孔提拉方式下, 内冷却系统温度控制方式术区温度低于外冷却系统的温度控制方式;在相同的冷却系统下, 2次钻孔提拉方式术区温度低于直接1次钻孔方式。其中, 采用内冷却系统进行温度控制时, 2次钻孔提拉方式的术区温度最低(P<0.05)。结论: 牙种植术中采用多次钻孔提拉方式及内冷却系统的温度控制方式, 可以有效降低术区温度, 减少手术产热, 提高牙种植术成功率。

关键词: 牙种植术, 钻孔提拉, 温度控制, 冷却系统

Abstract: PURPOSE: To study the effect of different ways of pulling the drilling burs and cooling systems on alveolar bone temperature of the surgical area, and explore the changes of temperature field in dental implants. METHODS: Forty-eight unified standard artificial (nylon) bone blocks were fabricated and divided into 6 groups according to different drilling pulling ways and cooling systems. The changes of bone temperature field were detected in 6 groups, and the highest temperature in temperature field was measured and recorded. The date was analyzed with SPSS 12.0 software package for ANOVA. RESULTS: The temperature in the surgical area using internal cooling systems under the same drilling pulling was lower than using external cooling systems. The temperature in the surgical area using secondary drilling pulling way was lower than using direct drilling methods under the same cooling systems. The temperature in the surgical area using secondary drilling pulling way was the lowest when internal cooling systems was adopted(P<0.05). CONCLUSIONS: Drilling pulling way and internal cooling systems can effectively reduce the temperature in the surgical area, lessen heat production and improve the success rate of dental implants.

Key words: Dental implant surgery, Drilling pulling, Temperature control, Cooling systems

中图分类号:

R780.4

刘道杨, 吴煜农, 陈宁, 彭伟, 廖文清, 王琰玲. 牙种植术中钻孔提拉方式及冷却系统对术区温度的影响[J]. 上海口腔医学, 2014, 23(2): 149-153.

LIU Dao-yang, WU Yu-nong, CHENG Ning, PENG Wei, LIAO Wen-qing, WANG Yan-ling. The influence of drilling pulling ways and cooling systems on dental implant surgery[J]. Shanghai Journal of Stomatology, 2014, 23(2): 149-153.

参考文献

[1] 张文捷, 陈建钢, 王莉, 等. 微创技术在老年患者牙种植术中的临床应用30例 [J]. 口腔医学, 2010, 30(10): 587-589.
[2] Abouzgia MB, James DF. Temperature rise during drilling through bone[J]. Int J Oral Maxillofac Implants, 1997, 12(3): 342-353.
[3] Eriksson AR, Albrektsson T. Temperature threshold levels for heat-induced bone tissue injury: a vital-microscopic study in the rabbit [J]. J Prosthet Dent, 1983, 50(1): 101-107.
[4] Eriksson RA, Albrektsson T. The effect of heat on bone regeneration: an experimental study in the rabbit using the bone growth chamber [J]. J Oral Maxillofac Surg, 1984, 42(11): 705-711.
[5] Piattelli A, Piattelli M, Mangano C, et al. A histologic evaluation of eight cases of failed dental implants: is bone overheating the most probable cause? [J]. Biomaterials, 1998, 19(7-9): 683-690.
[6] 颜彦, 周海静, 聂红兵. 医学领域中骨组织元素分析方法[J]. 口腔生物医学, 2012, 3(1): 41-44.
[7] Karmani S. The thermal properties of bone and the effects of surgical intervention [J]. Curr Orthop, 2006, 20(1): 52-58.
[8] Baqain ZH, Moqbel WY, Sawair FA. Early dental implant failure: risk factors [J]. Br J Oral Maxillofac Surg, 2011, 50(3): 239-243.
[9] 筱克, 谢群, 季林红, 等. 微创钻骨系统切削参数对切削力与温度的影响 [J]. 机械设计与制造, 2009, 47(2): 264-266.
[10] Harder S, Egert C, Wenz HJ, et al. Influence of the drill material and method of cooling on the development of intrabony temperature during preparation of the site of an implant[J]. Br J Oral Maxillofac Surg, 2013, 51(1): 74-78.
[11] Karaca F, Aksakal B, Kom M. Influence of orthopaedic drilling parameters on temperature and histopathology of bovine tibia: an in vitro study [J]. Med Eng Phys, 2011, 33(10): 1221-1227.