上海口腔医学 ›› 2026, Vol. 35 ›› Issue (5): 497-502.doi: 10.19439/j.sjos.2026.05.009

• 论著 • 上一篇    下一篇

3D打印个性化钛网联合浓缩生长因子膜在上颌前牙区骨增量及种植修复中的效果分析

彭莎莎, 周翔   

  1. 盐城市第一人民医院 口腔科,江苏 盐城 224006
  • 收稿日期:2025-12-17 修回日期:2026-01-23 发布日期:2026-11-05
  • 通讯作者: 周翔,E-mail: 466522473@qq.com
  • 作者简介:彭莎莎(1986—),女,硕士,主治医师,E-mail: sarasara1028@163.com
  • 基金资助:
    江苏省自然科学基金(BK20221301)

Analysis of 3D-printed personalized titanium mesh combined with CGF membrane in alveolar ridge defect and implant restoration of the maxillary anterior region

Peng Shasha, Zhou Xiang   

  1. Department of Stomatology, Yancheng First People's Hospital. Yancheng 224006, Jiangsu Province, China
  • Received:2025-12-17 Revised:2026-01-23 Published:2026-11-05

摘要: 目的: 分析3D打印个性化钛网联合浓缩生长因子(concentrated growth factor,CGF)膜在上颌前牙区骨增量及种植修复中的效果。方法: 选择2022年1月—2024年1月就诊的上颌单颗前牙缺失患者86例,采用随机数字表法分为对照组(3D打印个性化钛网,n=43)和试验组(3D打印个性化钛网联合CGF膜,n=43),比较两组种植前牙槽嵴骨量、疼痛程度、美学效果和种植后骨吸收、种植体稳定性及并发症发生情况。结果: 种植前,试验组牙槽嵴垂直骨量、唇腭侧骨量变化显著大于对照组(P<0.05)。种植后1周,两组疼痛程度评分显著降低(P<0.05),组间相比无显著差异(P>0.05)。种植后6个月,试验组牙红色-白色美学标准(pink esthetic score-white esthetic score,PES-WES)评分显著高于对照组(P<0.05);试验组牙槽嵴水平骨吸收量显著低于对照组(P<0.05),两组垂直骨吸收量相比无显著差异(P>0.05);试验组种植体稳定性优秀率显著高于对照组(P<0.05)。两组种植后未发生严重并发症。结论: 3D打印个性化钛网联合CGF膜用于上颌前牙区骨增量及种植修复,可显著增加种植前的牙槽嵴骨量,改善种植后的红白美学效果,减少水平向骨吸收,提高种植体稳定性。

关键词: 上颌前牙区, 牙槽嵴缺损, 引导骨组织再生术, 3D打印个性化钛网, 浓缩生长因子膜

Abstract: PURPOSE: To analyze the effect of 3D-printed personalized titanium mesh combined with concentrated growth factor (CGF) membrane in alveolar ridge defect and implant restoration of the maxillary anterior region. METHODS: A total of 86 patients with maxillary single anterior tooth missing who were treated from January 2022 to January 2024 were selected and divided into the control group (3D printing personalized titanium mesh, n=43) and the experimental group (3D printing personalized titanium mesh combined with CGF membrane, n=43) according to the random number table method. The alveolar ridge bone volume, pain degree, aesthetic effect before implantation, bone resorption, implant stability and the occurrence of complications after implantation were compared between the two groups. RESULTS: Before implantation, the vertical bone volume of the alveolar ridge and the bone volume on the labial and palatal sides in the experimental group were significantly higher than those in the control group (P<0.05). One week after implantation, the pain degree scores of both groups significantly decreased (P<0.05), and there was no significant difference between the two groups (P>0.05). Six months after implantation, the pink esthetic score-white esthetic score (PES-WES) of the experimental group was significantly higher than that of the control group (P<0.05); the horizontal bone resorption amount of the alveolar ridge in the experimental group was significantly lower than that in the control group (P<0.05), and there was no significant difference in the vertical bone resorption amount between the two groups(P>0.05). The rate of excellent stability of the implants in the experimental group was significantly higher than that in the control group(P<0.05). No serious complications occurred after the transplantation in both groups. CONCLUSIONS: The application of 3D-printed personalized titanium mesh combined with CGF membrane for alveolar ridge defect and implant restoration of the maxillary anterior region can significantly increase pre-implantation alveolar bone volume, improve pink-white esthetic outcomes after implantation, reduce horizontal bone resorption, and enhance implant stability.

Key words: Maxillary anterior region, Alveolar ridge defect, Guiding bone tissue regeneration surgery, 3D-printed personalized titanium mesh, Concentrated growth factor membrane

中图分类号: