反复熔铸对牙科烤瓷合金显微结构的影响

doi:10.19439/j.sjos.2018.06.005

上海口腔医学 ›› 2018, Vol. 27 ›› Issue (6): 585-590.doi: 10.19439/j.sjos.2018.06.005

反复熔铸对牙科烤瓷合金显微结构的影响

王颖卉¹, 邱芬芳², 潘宇¹, 吴维青³, 程辉¹

1.福建医科大学附属口腔医院修复科,福建医科大学口腔医学研究院, 福建医科大学口腔医学美学与生物力学研究中心,福建福州 350002;
2.福建省级机关医院口腔科, 福建福州 350002;
3.福州大学测试中心,福建福州 350002

收稿日期:2018-03-22 出版日期:2018-12-25 发布日期:2019-01-11
通讯作者: 程辉,E-mail：ch.fj@163.com
作者简介:王颖卉（1983-）,女,硕士,主治医师,E-mail：wyh9519@163.com

The effect of recasting on microstructure of dental ceramic alloys

WANG Ying-hui¹, QIU Fen-fang², PAN Yu¹, WU Wei-qing³, CHENG Hui¹

1.Department of Prosthodontics, School and Hospital of Stomatology, Oral Medicine Research Institute, Oral Medical Aesthetics and Biomechanics Research Center, Fujian Medical University. Fuzhou 350002;
2. Department of Stomatology, Fujian Provincial Governmental Hospital. Fuzhou 350002;
3. Test Center, Fuzhou University. Fuzhou 350002, Fujian Province, China

Received:2018-03-22 Online:2018-12-25 Published:2019-01-11
Supported by:
福建医科大学附属口腔医院科技创新领军人才项（2015-KQYY-LJ-3）

摘要/Abstract

摘要： 目的: 探讨反复熔铸对钴铬、纯钛、钯铜镓、金铂烤瓷合金显微结构的影响。方法: 在真空加氩气保护环境下,将4种烤瓷合金单纯反复熔铸1~3次。每次再熔铸前,烤瓷合金均经过课题组前期研究所得“烤瓷合金再熔铸前最佳处理方法”处理,根据金属显微组织检验方法（GB/T13298-2015）,分别对熔铸前、熔铸1~3次后的烤瓷合金进行研磨、抛光、浸蚀,采用金相显微镜或扫描电镜检测金相显微结构。结果: 随着熔铸次数增加,钴铬烤瓷合金晶粒粗化、晶粒间基质和晶界间化合物增多。纯钛烤瓷合金随熔铸次数增加,晶粒粗化明显。2次熔铸后,晶粒有等轴化倾向,3次熔铸则出现针刺状β相。钯铜镓烤瓷合金在2、3次熔铸后,晶粒结构略有长大。金铂烤瓷合金晶粒结构未随熔铸次数发生明显改变。结论: 反复熔铸显著改变钴铬、纯钛、钯铜镓烤瓷合金的显微结构,建议由厂家回收再利用烤瓷合金废旧料。

关键词: 烤瓷合金, 反复熔铸, 显微结构

Abstract: PURPOSE: To investigate the effects of recasting on metallographic microstructure of cobalt-chromium(Co-Cr), commercially pure titanium(cpTi), palladium-copper-gallium(Pd-Cu-Ga), aurum-platinum(Au-Pt) ceramic alloys. METHODS: Without adding new alloys, Co-Cr, cpTi, Pd-Cu-Ga and Au-Pt ceramic alloys were recasted for 1-3 times under the circumstance of vacuum compressive casting with argon. Before each recasting, these 4 ceramic alloys casted previously were treated by the most appropriate way which has been reported by our previous study. According to GB/T13298-2015 standards, the specimens of 4 ceramic alloys after recasting 1-3 times were grinded, polished, and etched and then the metallographic microstructure of them were determined by a metallographic microscope or scanning electron microscopy(SEM). RESULTS: With the increase of recasting times, the microstructure of Co-Cr ceramic alloy showed grain growth, grain matrix increase, and the intermetallic compound in the grain boundary increase, the microstructure of the cpTi ceramic alloy showed grain growth. The samples of cpTi ceramic alloy recasting twice appeared shaft tendency, and the ones which were recasted 3 times were compound of α-phase and β-phase. The microstructure of the Pd-Cu-Ga ceramic alloy showed grain growth slightly after casting 2-3 times, while no significant change was found on the microstructure of the Au-Pt ceramic alloy. CONCLUSIONS: Recasting changes the microstructure of Co-Cr, cpTi, and Pd-Cu-Ga ceramic alloys, and the ceramic alloys may recycled by the manufacturers.

Key words: Ceramic alloy, Recast, Microstructure

中图分类号:

R783.1

王颖卉, 邱芬芳, 潘宇, 吴维青, 程辉. 反复熔铸对牙科烤瓷合金显微结构的影响[J]. 上海口腔医学, 2018, 27(6): 585-590.

WANG Ying-hui, QIU Fen-fang, PAN Yu, WU Wei-qing, CHENG Hui. The effect of recasting on microstructure of dental ceramic alloys[J]. Shanghai Journal of Stomatology, 2018, 27(6): 585-590.

参考文献

[1] Peraire M, Martinez-Gomis J, Anglada JM, et al.Effects of recasting on the chemical composition, microstructure, microhardness, and ion release of 3 dental casting alloys and titanium[J]. Int J Prosthodont, 2007, 20(3): 286-288.
[2] 刘祥. 铸造合金力学机物理性能 [M]. 北京: 机械工业出版社, 1982: 101-175.
[3] Mirkovic N.Effect of recasting on the elastic modulus of metal-ceramic systems from nickel-chromium and cobalt-chromium alloys[J]. Vojnosanit Pregl, 2007, 64(7): 469-473.
[4] Reisbick MH, Brantley WA.Mechanical property and microstructural variations for recast low-gold alloy[J]. Int J Prosthodont, 1995, 8(4): 346-350.
[5] Al-Hiyasat AS, Darmani H.The effects of recasting on the cytotoxicity of base metal alloys[J]. J Prosthet Dent, 2005, 93(2): 158-163.
[6] Madani AS, Rokni SR, Mohammadi A, et al.The effect of recasting on bond strength between porcelain a base-metal alloy[J]. J Prosthodont 2011, 20(3): 190-194.
[7] Vaillant-Corroy AS, Corne P, De March P, et al.Influence of recasting on the quality of dental alloys: A systematic review[J]. J Prosthet Dent, 2015, 114(2): 205-211.
[8] Lin H, Zhang H, Li X, et al.Treatment of multiple ceramic alloys before recasting[J]. J Prosthet Dent, 2013, 110(1): 29-40.
[9] 杨松, 程辉, 李秀容, 等. 反复熔铸对钴铬烤瓷合金力学性能影响的研究[J]. 华西口腔医学杂志, 2011, 29(3): 249-252.
[10] 程辉, 杨松, 李秀容, 等. 反复熔铸对金铂烤瓷合金力学性能影响的研究[J]. 华西口腔医学杂志, 2013, 31(4): 412-414.
[11] 杨松, 程辉, 李秀容, 等. 反复熔铸对纯钛烤瓷合金力学性能影响的研究[J].上海口腔医学, 2014, 23(6): 651-653.
[12] 中国国家标准化管理委员会. GB/T13298-2015金属显微组织检验方法[S].
[13] 骆小平, 郭天文, 欧阳官. 铸模温度对铸钛机械性能及表面反应层结构的影响[J].中华口腔医学杂志, 1997, 32(6): 327-330.
[14] 李哲, 肖茂春. 铸造纯钛抛光方法的研究[J]. 华西口腔医学杂志, 2006, 24(3): 214-230.
[15] Okawa S, Hossain A, Kanatani M, et al.Surface properties of electrochemically buffed titanium casting[J]. Dent Mater J, 2004, 23(4): 504-511.
[16] 任丽萍, 李天侠, 林家婷, 等. 两种抛光方法对纯钛和钴铬合金粗糙度的影响[J].口腔医学研究, 2009, 25(6): 730-732.
[17] 李勇, 郑碰菊, 张建波, 等. 定向凝固技术的研究现状及发展趋势[J]. 材料导报, 2014, 28(23): 108-112.
[18] 赵伟, 程辉, 郑明, 等. 反复熔铸对镍铬烤瓷合金化学成分和微观组织结构的影响[J]. 中国组织工程研究与临床康复, 2009, 13(38): 7511-7516.
[19] 程辉, 陈南, 陈百欣. 牙科用非贵金属高熔铸造合金铸造前后金相比较研究[J]. 口腔医学纵横杂志, 2000, 16(3): 225-226.
[20] 龚媛媛, 王璐, 张全新. 热处理对牙用钴铬合金表面显微硬度的影响[J]. 第三军医大学学报, 2008, 30(7): 656-658.
[21] 潘鑫, 张晓东, 李玉洋. 修复体高熔合金材料钴铬合金铸造后性能研究[J]. 黑龙江医药科学, 2001, 24(3): 13-15.
[22] 连颂峰, 程辉, 马守治, 等. 反复熔铸对非贵金属烤瓷合金弯曲性能的影响[J]. 口腔医学研究, 2008, 24(3): 294-297.
[23] 张长源, 连颂峰, 吴维青, 等. 多次熔铸对Ni-Cr烤瓷合金拉伸性能的影响[J]. 福州大学学报(自然科学版), 2009, 37(4): 551-554.
[24] 王颖卉, 连颂峰, 程辉, 等. 反复熔铸对镍铬烤瓷合金硬度的影响[J]. 福建医科大学学报, 2010, 44(03): 199-201.
[25] 闫澍, 张玉梅, 施生根. 铸模的冷却方式对牙科纯钛铸件的力学性能影响的研究[J]. 口腔颌面修复学杂志, 2012, 13(3): 171-174.
[26] 高强. 最新有色金属金相图谱大全[M]. 北京: 中国冶金工业出版社, 2006: 1031-1041.
[27] 陈治清. 口腔材料学[M]. 北京: 人民卫生出版社, 2008: 179-184.
[28] Horasawa N, Marek M.The effect of recasting on corrosion of a silver-palladium alloy[J]. Dent Mater, 2004, 20(4): 352-357.
[29] 王颖卉, 杨松, 程辉, 等. 反复熔铸对钯基烤瓷合金力学性能影响的研究[J]. 口腔医学研究, 2013, 29(2): 132-134.

反复熔铸对牙科烤瓷合金显微结构的影响

The effect of recasting on microstructure of dental ceramic alloys

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	林泓磊, 江磊, 张长源, 林东红, 程辉. 反复熔铸对钴铬烤瓷合金细胞相容性的影响[J]. 上海口腔医学, 2017, 26(3): 246-250.
[2]	高燕，张富强，高建华. 稀土氧化物着色牙色四方多晶氧化锆陶瓷的烧结性能[J]. 上海口腔医学, 2015, 24(6): 679-686.
[3]	杨松, 程辉, 李秀容, 吴维青, 郑明, 王颖卉. 反复熔铸对纯钛烤瓷合金力学性能的影响[J]. 上海口腔医学, 2014, 23(6): 651-653.